220v Auto Infrared Body Motion Sensor Pir Sensing Switch 5.8ghz Microwave Radar Motion Sensor
New Products From This Supplier
Products Description
Product Paramenters /Microwave Radar Sensor
Instruction
* The sensor is an active motion detector
* It emits high-frequency electro-magnetic wave(5.8GHz) and receives their echo.
* The sensor detects the change in echo from even the slightest movement in its detection zone.
* A microprocessor then triggers the “switch light ON” command.
* Detection is possible through doors, panes of glass or thin walls.
Important: persons or objects moving towards the sensor are detected best!
Details Images for microwave radar sensor
Installation Instructions/Microwave Radar Sensor
* The sensor is an active motion detector
* It emits high-frequency electro-magnetic wave(5.8GHz) and receives their echo.
* The sensor detects the change in echo from even the slightest movement in its detection zone.
* A microprocessor then triggers the “switch light ON” command.
* Detection is possible through doors, panes of glass or thin walls.
Important: persons or objects moving towards the sensor are detected best!
Specifications for microwave radar sensor
Model No. |
microwave radar sensor BS029B |
Power Sourcing |
220V/AC-240V/AC |
Detection Range |
360° |
Detection Distance |
1-8m (radius) adjustable |
HF System |
5.8GHz CW radar, ISM band |
Ambient Light |
2-2000LUX (Adjustable) |
Time setting |
8sec-12min |
Transmission Power |
<0.2mW |
Power Consumption |
0.9W |
Installation sit |
Indoors ,ceiling mounting |
Rated Load |
1200W (220-240VAC) |
Practicality Fuctions /Microwave Radar Sensor
1) Reach setting (sensitivity)
Reach is the term used to describe the radii of the more or less circular detection zone produced on the ground after mounting the sensor light at a height of 2.5m, turn the reach control fully anticlockwise to select minimum reach (approx.1 m radii), and fully clockwise to select maximum reach (approx. 8m radii).
NOTE: the above detection distance is gained in the case of a person who is between 1.6m~1.7m tall with middle figure and moves at a speed of 1.0~1.5m/sec. if person’s stature, figure and moving speed change, the detection distance will also change.
2) Time setting
The light can be set to stay ON for any period of time between approx. 8sec (turn fully anti-clockwise) and a maximum of 12min (turn fully clockwise). Any movement detected before this time elapse will re-start the timer. It is recommended to select the shortest time for adjusting the detection zone and for performing the walk test.
NOTE: after the light switches OFF, it takes approx. 1sec before it is able to start detecting movement again. The light will only switch on in response to movement once this period has elapsed.
3) Light-control setting
The chosen light response threshold can be infinitely from approx. 2-2000lux. Turn it fully anti-clockwise to select dusk- to-dawn operation at about 2 lux. Turn it fully clockwise to select daylight operation at about 2000lux. The knob must be turned fully clockwise when adjusting the detection zone and performing the walk test in daylight.
The high-frequency output of this sensor is <0.2Mw- that is just one 500th of the transmission power of a mobile phone or the output of a microwave oven
Installation (see the diagram)/Microwave Radar Sensor
* Connect N, L with power
* Connect N, L’ with load
Note/Microwave Radar Sensor
* Electrician or experienced human can install it.
* The unrest objects can’t be regarded the installation basis-face.
* In front of the detection window there shouldn’t be hinder or unrest objects effecting detection.
* Avoid installing it near air temperature alteration zones for example: air condition, central heating, etc.
* For your safety. Please don’t open the case if you find hitch after installation.
* In order to avoid the unexpected damage of product, please add a safe device of 6A when installing infrared sensor, for
example, fuse, safe tube etc.
Some problem and solved way
The load don’t work:
a. Check the power and the load.
b. Whether the indicator light is turned on after sensing? If yes, please check load.
c. If the indicator light does not turn on after sensing, please check if the working light corresponds to the ambient light.
d. Please check if the working voltage corresponds to the power source.
The sensitivity is poor:
a. Please check if in front of the detection window there are hinder that effect to receive the signals.
b. Please check the ambient temperature.
c. Please check if the signals source is in the detection fields.
d. Please check the installation height.
The sensor can’t shut automatically the load:
a. If there are continual signals in the detection fields.
b. If the time delay is set to the longest.
c. If the power correspond to the instruction.
d. If the air temperature change near the sensor, air condition or central heating
Company Information
Establish in 2009 in ShenZhen, doing LED components, LED lighting, Motion Sensor Switch, OEM &ODM Product service. Nowadays BESTER is one of TOP 10 professional manufactures of LED components and Motion Sensor Switch in China.
Bester has her factory, and have necessary requirement for the production steps and test steps, we call it well regulated, So we can fast & flexible for customer requirement.
Our brand is Bester and Rayzeek.
We have modern production lines with more than 200 professional workers, their rich experience of making products ensure efficiency and stability .
With two warehouses both are more than 500 square meters, to store the finished products, the space is sufficient and safe.
*Our company passed the ISO9001: 2000 quality management system certification.
*New products are launched every year, and old products are being updated
Advanced automation equipment
All of our products are produced by our private molds, and we have lots of produce machines, with rich experience in ODM, we can
do ODM for our customers with successful cases.
Our Advantage
Packing&Shipping
♦PACKING: Neutral packing with new carton or according to customer requirements.
♦PAYMENT: T/T,Paypal,West Union,30% deposit, 70% balance before delivery.
♦LEAD TIME: Sample in 1-5 working days and large order in 12-15 working days.
♦TRANSPORT: By DHL/UPS/FEDEX, Air cargo or Sea shipment.
♦PORT OF SHIPMENT: FuTian,Shenzhen,China.
♦MOQ: 1 piece. Providing DISCOUNT and OEM service for large order.
All products have CE RoHS certification, and some products have UL certification
Business Nature
Manufacturer
Country/Region
Shenshan, China
Main Products
Pir Motion Sensor, Led Cabinets Sensor, Wall Swiches...
We mainly produce Sensor Switches, PIR sensors and IR sensors with brand new designs and molding techniques. Our products are all assembled according to UL standards and CE certification and can fit all kind of installations and wall mounting fittings.